Script To Create A Swapfile On Linux

Script To Create A Swapfile On Linux

Category : How-to

Get Social!

This 5 line script will quickly create a 512MB SWAP file that will be automatically mounted on each machine reboot. It assumes you don’t already have a swap file enabled.

The script creates a 512MB file called .swapfile on your root partition, makes it SWAP format and enables it as available system SWAP. An fstab entry is also added so that it’s mounted after a machine reboot.

You can find more detailed instructions and explanations on this blog post. With some file systems, fallocate may not work – again, take a look at  this for a work around.

fallocate -l 512M /.swapfile
chmod 600 /.swapfile
mkswap /.swapfile
swapon /.swapfile
echo "/.swapfile none swap defaults 0 0" >> /etc/fstab

Proxmox OpenVZ SWAP and Performance

Get Social!

openvz-logo-150px_new_3 I have been having trouble with a Proxmox node which is only running OpenVZ containers however it is at the upper limit of its RAM resources. Over time, I noticed that Proxmox used SWAP (virtual memory, page file, etc), quite aggressively, to make sure there was always some RAM free. That sounds fantastic, and is just what I would expect the Proxmox server to be doing, except it does it all too well. Proxmox made sure that around 40% of the RAM on the host machine was free at the expense of moving many running processes across all the running containers to SWAP. This is how Linux works, by design, and is expected behaviour. Running processes which have memory which hasn’t been touched in a while have their memory moved to SWAP. This allows other applications which need the memory right now to use it and anything left over can be used as cache by the kernel. When a process with memory in SWAP needs to use that memory, it needs to be read from SWAP and back into memory so that it can be used. There is a huge overhead with this process and will often be noticed when you use a container which has not been used in a while – at the start everything will be slow until all the required memory items have been read from SWAP and put back into RAM. To help with this situation we can do two things:

  • Make sure SWAP is always on a fast disk with plenty of free IO bandwidth. On a small installation, this should not be on the same disk as your container file systems. SSDs can also bring a huge performance benefit over conventional mechanical drives.
  • Reduce the amount of RAM which Proxmox keeps free by making the algorithm which moves memory to SWAP less aggressive.

Move SWAP to fast storage

Generally, and when installing Proxmox for the first time a SWAP partition will be created on your hard disk. By default, this will be the same partition as your Proxmox operating system and your container storage. On a slow mechanical disk, this will result in far too much IO concurrency – that is different processes trying to read or write to a disk at the same time – which will massively affect server performance. One thing we can move to another disk is system wide swap.

You can either use a new file, disk, partition or block device for your new swap location. You will then need to turn your old SWAP device off to stop it from being used. Use the below examples to move your SWAP device.

See this post for a quick script to automatically create a SWAP file.

Make a new SWAP device as a file

Create a file on your file system and enable it to be used as a SWAP device. The below example uses the mount /mnt/swapdrive and the file swapfile to use as your new swap device with a size of 4096 MB.

dd if=/dev/zero of=/mnt/swapdrive/swapfile bs=1M count=4096

You will then need to format the file as SWAP with the below command.

mkswap /mnt/swapdrive/swapfile

Make a new SWAP device as a partition

Use the below command to use a drive partition as your new SWAP device. The below example uses /dev/sdc3 as your SWAP partition. You must have precreated this partition for it to be available.

mkswap /dev/sdc3
swapon /dev/sdc3

Turn a new SWAP device on

Once you have a new SWAP device created, either a file or a disk or partition you will need to enable it. Use the swapon command. The below shows an example of a file and disk partition command:

swapon /mnt/swapdrive/swapfile
swapon /dev/sdc3

Turn off the old SWAP device

To turn off the old SWAP device, first identify it using swapon -s.

swapon -s

Then, use the swapoff command to turn the device off. The below example is the default Proxmox SWAP device location.

swapoff /dev/mapper/pve-swap

Clear SWAP space without rebooting

You can clear your SWAP memory by turning the system wide SWAP memory off and then back on again. Run the below commands to turn off your system wide SWAP space forcing all the SWAP to be read back into RAM. You must have enough RAM for available on your system for this to work correctly. Once this has completed, run the second command to turn SWAP back on again. You can also use this to make your SWAP memory changes take effect.

swapoff -a 
swapon -a

Make the SWAP file persist after rebooting

To make sure your SWAP file is mounted the next time your machine reboots you’ll need to add an entry to the fstab file.

Open the fstab file with your text editor:

vi /etc/fstab

And add a line, similar to the below making sure the first attribute is the location of your newly created SWAP file.

/mnt/swapdrive/swapfile  swap  swap  defaults  0  0

Change the ‘swapiness’ setting

To change how aggressively Proxmox, or other Linux distribution, moves process memory to SWAP we have a swapiness attribute. The swapiness setting is a kernel setting which is permanently set in the /etc/sysctl.conf file, or temporarily using sysctl.

The swapiness setting takes a value between 0 and 100. Using 0 will virtually turn off using SWAP, except to avoid an out of memory exception (oom). Using a value of 100 will cause the system to use SWAP as often as possible and will likely degrade system performance servilely. A value of 60 is the default for Proxmox.

Change the swapiness value for the current boot

To change your swapiness value for the current boot, use the below command. The value will be reset after rebooting. The following example will set the swapiness value to 20.

sysctl -w vm.swappiness=20

Permanently change the swapiness value

Use the below command to permanently change your swapiness value. Note that this will not affect the current boot.

vi  /etc/sysctl.conf

And add the following to give a swapiness of 20

vm.swappiness=20

Visit our advertisers

Quick Poll

Do you use GlusterFS in your workplace?

Visit our advertisers